There are many times you wish to a specific device of your own to reduce volumes or any measurements of your concern. An example could be your audio equipment, deflections in a cantilevered stairway, or even the noisy tachometer of your motorbikes. For these adjustments, you may opt to use a potentiometer which is a variable resistor.
With an understanding of how circuitry and an equation works, you can make use of a device that could help regulate the voltage amount of the audio equipment or other electronics. A voltage divider is a passive type of line that produces an output value. This value is the lowered amount of initial voltage.
The Ohms law is used to understand the result of this device. It states that current flowing in a conductor is proportional to the difference between its ends. Meaning, if the current is reduced, then the Volt is also reduced.
There are two essential parts of this divider, one is the circuit and the other is the equation. The circuit pertains to a source of the Volt which goes across two resistors. For the equation, you have to assume three values namely input voltage, resistor one R1, and resistor two R2. The output value could be found by taking the ratio between R1 and R2.
Knowing these essentials, you may realize that you can also create your own portable divider. For this, you have to prepare the leads, resistors, alligator clamps, snap on connectors, a voltmeter and a standard 9V battery. This is the highest possible amount of V a simple electronic can handle. Some would limit it to a 5V only.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
The new positive terminal. After having a new set up for your circuit, the positive terminal will now be the connector which is attached to the twisted part of the resistors. However, the negative terminal remains the same. Using the Ohms law, you will understand how a 10 ohm resistor and a 20 ohm resistor with a 9V energy source will now have a new output charge of 3V.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
With an understanding of how circuitry and an equation works, you can make use of a device that could help regulate the voltage amount of the audio equipment or other electronics. A voltage divider is a passive type of line that produces an output value. This value is the lowered amount of initial voltage.
The Ohms law is used to understand the result of this device. It states that current flowing in a conductor is proportional to the difference between its ends. Meaning, if the current is reduced, then the Volt is also reduced.
There are two essential parts of this divider, one is the circuit and the other is the equation. The circuit pertains to a source of the Volt which goes across two resistors. For the equation, you have to assume three values namely input voltage, resistor one R1, and resistor two R2. The output value could be found by taking the ratio between R1 and R2.
Knowing these essentials, you may realize that you can also create your own portable divider. For this, you have to prepare the leads, resistors, alligator clamps, snap on connectors, a voltmeter and a standard 9V battery. This is the highest possible amount of V a simple electronic can handle. Some would limit it to a 5V only.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
The new positive terminal. After having a new set up for your circuit, the positive terminal will now be the connector which is attached to the twisted part of the resistors. However, the negative terminal remains the same. Using the Ohms law, you will understand how a 10 ohm resistor and a 20 ohm resistor with a 9V energy source will now have a new output charge of 3V.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
Aucun commentaire:
Enregistrer un commentaire