Certain reasons may drive you to repair your television. This includes your device powering itself off or taking a long time to get reception when you turn it on. The good thing is that such problems can be resolved by repairing the TV power supply. The process is not very hard when you have proper guidelines.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Check to see the capacitors that are malfunctioning. Capacitors assume the shape of tiny cylinders and only vary in their length and width. Since most of them may appear normal, search for those that have bulged at the surface or are removing a brownish to yellowish liquid on the surface. This means that they have been overheated leading to the problem you are facing. Make sure that no damage is done to copper pads when removing them.
Once you remove the faulty ones, use the new ones to replace them. Take note of the positive polarity and negative polarity when substituting them. You should then indicate the negative leads that are on the board using the soldering iron. The negative section is characterized by a grey stripe. Since the capacitors are polarity sensitive, make sure they are installed well.
After replacement, you ought to reassemble your television to check power. When you have substituted the connectors and have reattached the back panel and the bolts, check if the problem has been rectified. A power surge is the likelihood of the fuse blowing. Therefore if the issue has not been settled, check the fuse. Look for a suitable fuse for your device for replacement.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Check to see the capacitors that are malfunctioning. Capacitors assume the shape of tiny cylinders and only vary in their length and width. Since most of them may appear normal, search for those that have bulged at the surface or are removing a brownish to yellowish liquid on the surface. This means that they have been overheated leading to the problem you are facing. Make sure that no damage is done to copper pads when removing them.
Once you remove the faulty ones, use the new ones to replace them. Take note of the positive polarity and negative polarity when substituting them. You should then indicate the negative leads that are on the board using the soldering iron. The negative section is characterized by a grey stripe. Since the capacitors are polarity sensitive, make sure they are installed well.
After replacement, you ought to reassemble your television to check power. When you have substituted the connectors and have reattached the back panel and the bolts, check if the problem has been rectified. A power surge is the likelihood of the fuse blowing. Therefore if the issue has not been settled, check the fuse. Look for a suitable fuse for your device for replacement.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
About the Author:
To help you get your TV power supply, simply go to our online page for details. You will find all the relevant information by clicking here http://www.tekbyus.com.
Aucun commentaire:
Enregistrer un commentaire